sampler
Sampling with the sample key
opens a record page from any screen: set source, gain and threshold, then arm the recorder — on the library page, a key and then on the drum sampler and multisampler, a keyboard key on the synth sampler. The take starts once the input passes the threshold.
Every record page runs in the same order: choose the source, set the gain against the meter, put the threshold just above the room noise, then arm. Arming only readies the recorder; the take begins with the first sound that passes the threshold, so it starts on the note rather than on silence. Each engine's unit has its own key handling.
How to
Record a sample into the library
before you start the selected track does not use a sampler engine
- 1
- 2 the source; picks the channel of line in or USB
- 3 the gain, watching the level meter
- 4 the threshold, just above the room's noise
- 5 arms the recorder; the take starts when the sound passes the threshold
- 6 listen back; throws the take away instead
The take is saved to the library (by TE's how-to, in its user folder) unless you press .
Details
- TE’s guide
On a sampler track, opens that engine's record page; on other tracks it records a stand-alone sample for the library.
- TE’s guide
A sample can be at most 20 seconds long, in every sampler.
- TE’s guide
On the library record page (a track without a sampler engine), holding arms the recorder.
- TE’s guide
Every record page has a threshold on , the level at which recording begins, so arming alone does not start the take; it starts when the input rises past that level.
- TE’s guide
On the drum sampler and multisampler record pages you first press the keyboard key the take should go to (it lights up), then .
- TE’s guide
The synth sampler's record page starts sampling from a keyboard key, which also becomes the sample's root note; the guide gives that page no gesture.
- TE’s guide
The guide does not say what ends a take before the 20-second limit, such as whether letting go of stops it; not yet checked on a unit.
- worked out
The level meter previews the input while you set the gain, and TE's pictures draw the threshold as an orange line across it.
- TE’s guide
On the library record page, plays the take back and deletes it before it reaches the library.
- worked out
A stand-alone take should land in the library's user folder (samples → user over MTP). The sample chapter says only that it goes to the library, but TE's load-samples how-to names user as the folder for samples recorded on the unit; not yet checked on a unit.
- TE’s guide
Pressing the lit track key closes the record page.
- TE’s guide
The sources TE documents for the sample page are the built-in mic, line in and USB; the guide names line in and USB as the ones with an input channel and draws the page with the mic selected. Tutorial videos on OS 1.0.x show a longer list, see the record-sources fact.
- worked out
The guide never offers headset on the sample page and lists it among the external audio track's inputs (); tutorial videos do show a headset mic on the record page, see the record-sources fact.
- TE’s guide
The built-in microphone can be the source, so sampling needs no cable.
- TE’s changelog
Picking the input channel for line in and USB arrived in OS 1.0.29.
- disputed
TE's audio-interface how-to picks the USB channel with instead; not yet checked on a unit.
- community
The record page's sources run mic, headset mic, line in and then resample last (a tutorial video on OS 1.0.x; the page's USB entry was not seen in that list).
- community
The record page's gain runs up to +31, and the screen prints the lowest and middle settings as +0 (two videos, OS 1.0.x).
- community
Beside the source icon the page shows the letters L and R for the input channel; shift + E1 changes which is lit (one video, OS 1.0.x).
- community
Resample records what the unit itself plays, so the meter stays silent until the transport is running (one video, OS 1.0.x).
- community
A take is named project, note, track and .wav joined by hyphens, in lower case, for example unnamed-f2-5.wav (three videos). The note uses C3 = 60 and the track counts from 1. A stand-alone library take uses F2 and the current track, a drum or multisampler take uses its key's note, and a synth sampler take uses its root note.
Parameters
| parameter | gesture | range | cc |
|---|---|---|---|
| source sample | mic / headset mic / line in / resample | – | |
| input channel sample | – | – | |
| gain sample | – | – | |
| threshold sample | – | – |