sampler
Synth sampler
Plays one sample across the keyboard. On its record page a keyboard key starts sampling and becomes the root note; sets start, loop and end points, and its shift layer direction, tune, loop crossfade, gain and loop type.
TE's guide calls it the one shot synth sampler. To record, open , set source, gain and threshold, then press the key whose pitch matches the sound you are about to play: the take is tuned to that key, so the keyboard plays it in tune. Loop forever suits drones and pads, loop until release leaves a natural tail when you let go, and loop off makes the sample a one-shot.
How to
Record a new sample into the synth sampler
before you start the track uses the synth sampler
- 1 the synth sampler's record page
- 2 the source; sets the gain and the threshold
- 3 the note the sample should play at; this starts sampling
The sampler tunes the take to the key you pressed.
Details
- TE’s guide
On the synth sampler's record page you start sampling by pressing a keyboard key; the guide gives this page no gesture.
- TE’s guide
The key you press becomes the sample's root, the note the sampler tunes the recording to.
- worked out
The page has the same source, gain and threshold controls as the other record pages (, , ), so the key arms the recorder and the take begins once the input passes the threshold.
- worked out
TE's picture of this record page reads "press key to sample" and labels none of ….
- TE’s changelog
OS 1.0.45 corrected a latch text that the sample screen shows for the synth sampler; the changelog gives no wording, so the prompt on OS 1.1.33 may differ from TE's picture.
- TE’s guide
Not documented and not yet checked on a unit — whether also records here, whether the key has to stay held, and what ends a take before 20 seconds.
- TE’s guide
Pushing the encoder in while moving one of the four points gives finer steps.
- TE’s guide
Loop start at the very end of the sample means no loop.
- TE’s guide
Loop forever keeps cycling after release, loop until release stops cycling when you let go, loop off plays straight through.
- community
After sampling on the unit, the loop runs from 20 % to 80 % of the sample, set to loop forever.
- community
Tune works in cents; sample gain spans −30 to +20 dB.
- TE’s changelog
Synth sampler settings accept parameter locks.
- worked out
In the replica a held step locks what turns, start, loop start, loop end and end, and with direction, tune, loop crossfade and gain, but not the loop type, which is a click; the changelog does not list them, and they are not yet checked on a unit.
- checked on a unit · 1.1.33
The page shows an overview strip of the sample on top (base layer only), the left and right waveforms, and start, loop and end markers.
- checked on a unit · 1.1.33
With held it shows direction, tune as a note symbol and a value such as −12.00, crossfade as a percentage drawn as a dark wedge at the loop, and gain.
- checked on a unit · 1.1.33
CC12–15 on the track's channel move nothing on this page.
- checked on a unit · 1.1.33
Loop crossfade runs from 0 to 75 %, drawn as a dark wedge sloping down into the loop end over that share of the loop.
- community
A synth sampler take is named after its root note in the project-note-track.wav pattern, for example unnamed-c3-2.wav (community, OS 1.x).
Parameters
| parameter | gesture | range | cc |
|---|---|---|---|
| sample start M1 | – | – | |
| loop start M1 | – | – | |
| loop end M1 | – | – | |
| sample end M1 | – | – | |
| direction M1 | forward / backward | – | |
| tune M1 | – | – | |
| loop crossfade M1 | – | – | |
| sample gain M1 | – | – | |
| loop type M1 | loop forever / loop until release / loop off | – |